fountain pens

Eye Dropper Challenge 3/5 Lamy Vista


Challenge number three is the one I was dreading the most…not because I don’t like the pen. Quite contrary. I love Lamys and I simply didn’t want to destroy a perfectly good pen. Bureau sells Vista Rollerball barrel replacements on daily basis (hint, hint)…Jo got me and Faisal one each, so we could do this. Thanks Jo! πŸ™‚

Lamy Vista isn’t the easiest pen to convert, but it is possible. Vista fountain pens have two ink windows (ink would leak out). Vista roller-ball pen looks similar. It doesn’t have an ink window, but it does have breather holes at the top. Here is where Epoxy comes in. I have used 2-part clear epoxy resin glue.Β There are many threads on FPN and YouTube videos. People have used all sorts of super glues, plastic glues, but I wanted something clear and ‘invisible’. Long story short: I have swapped the barrels and sealed the holes. Now let’s have a look how I’ve done it.

Materials needed:

Lamy Vista rollerball barrell (available here)
Silicon Grease (clear 100% that you can find in hardware stores)
O-ring (7mm in, 9mm out, 1mm thick)
Epoxy Resin Glue (Devcon 5-minute Epoxy)
Square tea mug and scotch tape
Food zip-lock bag (just in case)

Instructions – just a friendly warning, this will take a day or two πŸ˜‰

  • prepare Epoxy. Squeeze some epoxy in the mixing bowl (you will need a pea size drop) and quickly stir with the stick into small puddle (both included in the package I bought)
  • grab Vista Rollerball barrel and dunk it in the epoxy. Just the end bit of course πŸ˜‰ I think that this is the most important step of them all. Using a Q-tip or brush would not give same result!
  • turn the barrel upside down and slowly rotate in hand (this will help the glue to get everywhere)
  • inspect the end bit to make sure that it is completely covered with epoxy (you will notice that the glue will start to set very quickly. Don’t panic, this is a good thing!)
  • let it set for good 5 minutes and inspect again. Mine was set by now and I was very happy with the way it turned out. Glue was almost invisible and it was nice and round. No sharp corners, no residue. Epoxy went inside the holes and not on the outside. Yeey!epoxy on Vista
  • leave the barrel for 24-hours to make sure epoxy has dried completely
  • use the syringe and plain water to test if the end of the barrel is completely sealed
  • if it is, the you can get rid of the water and let the barrel dry
  • once dried, secure the barrel to something so it will stay up ( I have used square tea mug and some scotch tape)
  • fill syringe with ink, for testing purposes I have only used 3ml of ink (2x more than Lamy cartridge capacity)
  • empty the ink into barrell
  • get Vista section and push O ring to the end of threads
  • apply silicone grease to the section threads using Q-tip
  • screw section onto barrel which has been filled with ink. Wipe excess silicone (if any)
  • you are good to go!!!!
  • pen will prime itself and should write almost immediately
  • last step – even tho I had no leaks I put the pen into a zip-lock bag when I wasn’t using it

And here is what my eye-dropper Vista looks like:

vista_MG_9733 vista_MG_9741 vista_MG_9732

Gorgeous!!!!! I have inked my pen with Private Reserve Blue Suede (teal inks are super cool).

Faisal has pointed out, that Neonlime ink would look great inside, so I am on a hunt to get a bottle πŸ˜‰ Fluorescent highlighter ink looks great under UV light. So it happens, we have UV torch in the office πŸ˜‰

Mishka (^_~)
Lamy Vista converted into an Eye Dropper